Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Installation for Johns Creek Homeowners
A new gate installation in Johns Creek typically runs $2,800-$8,500 depending on gate type, material, and whether the job includes automation, power routing, and safety edges. Most residential driveway gate installations take 1-3 days from measure to final walkthrough, with Vance Gate Repair providing a written, itemized price before any work begins. Call (678) 394-1765 for a free measure and written estimate.
We’ve installed and serviced over 22,000 gates since 2014, and the ones that last in Johns Creek are the ones measured twice and documented once. The clay-heavy soils in this part of Fulton County shift with seasonal moisture, which means post depth, concrete footing specs, and hinge alignment can’t be eyeballed. Adrian Vance built this company on commercial access-control documentation habits, and that same standard applies to every residential driveway gate we install in Johns Creek: written scope, written price, photographic evidence of every post setting and limit-switch reading. Under The Haven Standard, you get the price in your hand before we pick up a tool, and a photo log of what we found and what we left behind before we drive away.
What Our Gate Installation Service Includes
Driveway Gate Installation
A driveway gate is the primary vehicle access point for your Johns Creek property, typically spanning 10-16 feet for single openings or 20-24 feet for double configurations. Most homeowners in Johns Creek install these at the street entrance to control access, improve security, and increase property value in neighborhoods like St. Ives Country Club and The Falls of Autry Mill. We measure your opening, check the grade and drainage pattern, specify the right post depth for local soil conditions, and deliver a written price that includes the gate frame, hardware, automation if requested, and the power run from your house to the motor location.
Pedestrian Gate Installation
A pedestrian gate is a smaller walk-through opening, usually 3-4 feet wide, installed alongside a driveway gate or at a separate walkway entrance. In Johns Creek, we see these most often on corner lots in Country Club of the South and along the golf-course properties where foot traffic between homes and amenities is common. We install pedestrian gates with self-closing hinges, magnetic latches, and lockable hardware; if you want keypad or card access, we integrate the wiring into the same access-control system as your main gate.
Sliding Gate Installation
A sliding gate moves horizontally on a track or cantilever system, making it the right choice when your Johns Creek driveway slopes upward from the street or when a swing gate’s arc would intrude on the driveway space. We’ve installed sliding gates along Medlock Bridge Road properties where the approach is tight, and in subdivisions like Abbington where setback requirements limit swing clearance. Our installation includes the track or cantilever frame, guide rollers, motor mounting, and limit-switch calibration; we photograph every roller alignment and track-level reading for the job record.
Swing Gate Installation
A swing gate rotates on hinges mounted to posts or columns, either single-leaf or double-leaf, and remains the most common residential style in Johns Creek. The key detail most installers miss is the post footing: in Johns Creek’s expansive clay, a 36-inch minimum depth with proper drainage gravel prevents the frost-heave and seasonal settling that throws hinges out of alignment. We set posts on compacted base material, plumb them with a digital level, and document the footing depth and concrete mix for the photo record you receive at completion.
Double Gate Installation
A double gate uses two leaves that meet in the center, reducing the swing arc per leaf and accommodating wider openings without the track system a sliding gate requires. In Johns Creek, double gates work well on estate properties in neighborhoods like Rivermont and Crooked Creek, where the entrance may exceed 20 feet. We install center-drop pins, cane bolts, or electric strikes depending on your preference, and we synchronize the motor timing so both leaves reach their limits simultaneously without gap or overlap.
Security Gate Installation
A security gate prioritizes controlled access with features like anti-climb design, integrated intercoms, keypad or card readers, and video verification. Johns Creek homeowners near the Gwinnett County line and commercial properties along State Bridge Road request these most often. We install the gate structure, run low-voltage wiring for access control, program the entry devices, and leave you with a wiring diagram and device map so any future technician knows exactly what’s in the ground without reverse-engineering the work.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Installation
We install and service nine major gate automation brands, which means we match the motor to your gate type and usage pattern rather than forcing a single product line. For Viking operators, we’ve installed hundreds of their heavy-duty slide and swing units on commercial and residential sites throughout North Fulton; we stock Viking OEM parts and can source their V-Series and L-Series motors with standard lead times. Ghost Controls systems are popular for lighter residential swing gates in Johns Creek subdivisions, and we keep their DPS and TSS models in rotation for properties with 12-14 foot single-leaf openings where quiet operation matters.
DoorKing remains a standard for multi-tenant and estate properties with telephone entry integration; we’ve programmed their 1830 and 1833 series for Johns Creek homeowners who want visitor call-forwarding to their cell phones. Elite operators handle high-cycle applications well, and we’ve installed their CSW and SL series on gates with daily open counts above 50. Whether you have Viking, Ghost Controls, DoorKing, Elite, or any other make already on your property, we can service it, source parts for it, or specify a compatible replacement if the unit is beyond repair. We don’t steer customers toward replacement when repair is the right call.
BeforeAfterSigns You Need Gate Installation Right Now
- Your current gate sags or drags on the ground. A gate that no longer clears the driveway surface has hinge failure, post rot, or frame distortion. In Johns Creek’s humid climate, wooden posts deteriorate faster than homeowners expect, and steel frames stress-crack at weld points if the gate was undersized for its span. Continuing to operate a dragging gate damages the motor and risks the gate falling off its hinges entirely.
- The frame is visibly bent or twisted. Impact damage from vehicles, falling limbs, or gradual overload from added weight (decorative ironwork, climbing vines) distorts the gate geometry. A twisted frame places uneven load on the motor and hinge hardware, accelerating wear on every connected component. We measure frame squareness with a digital level and recommend replacement when deviation exceeds 3/8 inch over a 10-foot span.
- You’re adding automation to a manually operated gate that wasn’t built for it. Not every gate frame can handle the torque and back-pressure of a motorized operator. Lightweight aluminum or thin-wall steel gates flex under motor stress, causing premature operator failure and erratic limit-switch behavior. We evaluate your existing gate for motor compatibility and specify a reinforced replacement if the structure won’t support reliable automation.
- Your property has no gate at all and you’re experiencing unauthorized access. Johns Creek residents near multi-use paths, parkland, or commercial corridors report unexpected foot and vehicle traffic. A properly installed gate with access control creates a documented barrier; we can integrate photo-eye safety beams, loop detectors, and keypad entry to match your security requirements.
- The gate is more than 20 years old and repairs are becoming frequent. Multiple service calls in a single year often indicate systemic failure: corroded internal framework, obsolete parts availability, or motor technology that predates modern safety standards. We track your repair history and provide an honest assessment of whether replacement costs less over a 5-year horizon than continued patching.
Our Gate Installation Process - Step by Step
- 1
Free on-site measure and consultation. We visit your Johns Creek property, measure the opening, assess grade and drainage, identify underground utility locations, and discuss your preferences for gate type, material, automation, and access control. You get a written checklist of what we observed, with photos of the site conditions.
- 2
Written estimate delivered within 24 hours. Under Haven Standard Clause 1, we itemize every component: gate frame, posts and footings, hardware, motor and controls, power run, safety devices, and labor. The price is flat and fixed; no line reads “TBD” or “plus materials.” You approve in writing before we schedule.
- 3
Permit assistance if required. Johns Creek and Fulton County may require permits for structural gates or electrical work beyond low-voltage automation. We prepare the gate specifications and site plan for your permit application; we don’t pull permits in our name, but we give you the documentation package that makes the process straightforward.
- 4
Fabrication and site preparation. For custom gates, we fabricate to measured dimensions in our shop, then return to set posts and footings. Post holes are augered to depth, base material is compacted in 6-inch lifts, and concrete is poured with the post plumb-checked in two axes. We photograph footing depth, concrete slump, and post plumb readings.
- 5
Gate hanging, automation, and final calibration. We hang the gate, install and program the motor, set limit switches to exact travel endpoints, align photo-eyes and safety edges, and test all access-control devices. Before we leave, we photograph every adjustment point, provide you the photo log and wiring diagram, and walk you through operation and manual override procedures. The 365-Day Done Right Promise takes effect immediately.
How Much Does Gate Installation Cost in Johns Creek?
A typical manual swing gate installation in Johns Creek runs $2,800-$4,200 for a standard 12-foot aluminum or steel single-leaf gate with posts, hardware, and basic latch. For more on gate installation pricing, see our detailed breakdown below. Adding automation with a mid-range operator and safety package brings most residential swing-gate projects to $4,500-$6,800. Sliding gate installations start higher due to track or cantilever engineering, typically $5,200-$8,500 for residential openings up to 20 feet with automation included. Double gates fall in a similar range to single swing gates for the gate itself, with motor synchronization adding $400-$800 to the automation package.
Several factors move these numbers. Material choice matters: wrought-iron-style steel costs more than aluminum, and wood requires more frequent maintenance in Johns Creek’s humidity. Site conditions affect labor: a steep grade, buried utilities, or a long power run from the house to the gate location adds time and materials. Access-control complexity, telephone entry, video integration, and multiple remotes or key fobs layer on additional cost. We itemize every factor in the written estimate so you see exactly what drives the price.
To avoid overpaying, get at least one competing written estimate and bring it to us. We offer a free second-opinion review of any other company’s paperwork; we’ll flag scope gaps, specification mismatches, or hardware downgrades that explain a lower price. What’s included in our free estimate: the site visit, measurement, written itemization, and permit documentation package. There is no obligation to proceed, and we don’t pressure for a decision on the spot.
Gate Installation Near Johns Creek - Our Service Area
We install gates throughout North Fulton and into Gwinnett and Forsyth counties, with typical response times of 30-45 minutes to Duluth, Alpharetta, and home base in Johns Creek. Norcross, Roswell, Milton, and Sugar Hill are regular service stops; Lilburn, Sandy Springs, Cumming, Lawrenceville, and Buford fall within our standard scheduling radius. We don’t charge travel fees within this zone, and we don’t subcontract installation work to crews we haven’t background-checked and uniformed ourselves.
Serving Johns Creek, GA - Our Local Coverage Area
We’re based in the Johns Creek area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Installation in Johns Creek
Duluth gate installation follows the same process as ours: measuring, fabricating, and securing a new gate structure at your property entrance, including posts, hardware, and optional automation. At Vance Gate Repair, every installation in Johns Creek includes a written scope and price before work starts, photographic documentation of post footings and final adjustments, and the 365-Day Done Right Promise. Call (678) 394-1765 for a free measure and written estimate.
Most residential gate installations in Johns Creek take 1-3 days from first post-setting to final walkthrough, with custom fabrication adding 1-2 weeks before site work begins. Simple manual swing gates on prepared openings often complete in a single day; sliding gates with track systems and full automation typically need 2-3 days for proper alignment and safety-device testing. We give you a specific schedule in the written estimate, not a range.
Manual swing gate installations typically run $2,800-$4,200; automated swing gates $4,500-$6,800; and sliding gates $5,200-$8,500 depending on size, material, and access-control features. Every estimate from Vance Gate Repair is itemized and fixed; the price you approve is the price on the invoice. Call (678) 394-1765 for an exact quote - estimates are free.
Yes. We install, program, and repair Viking, Ghost Controls, DoorKing, and Elite operators, along with five additional major brands. We stock common parts for these manufacturers and can source OEM components with standard lead times for less common items. If your property already has one of these brands, we service it; we don’t push replacement unless the unit is genuinely beyond repair.
We don’t perform same-day gate installation - proper measurement, fabrication, and concrete curing can’t be rushed without compromising the structure. However, a live person answers our phone 24 hours a day, seven days a week, and we can often schedule a measure within 24-48 hours for urgent situations like security breaches or insurance requirements. For immediate security needs, we may recommend temporary measures while the permanent gate is fabricated.
All completed gate installation work is covered by our 365-Day Done Right Promise: if anything about the installation is not right, we make it right at no additional charge within one full year. This covers workmanship, hardware function, and automation performance. Manufacturer warranties on motors and electronics run separately and vary by brand; we register your equipment and provide the warranty documentation before we leave.
Clear vegetation and obstacles from the proposed gate line so we can measure accurately and identify underground utility paths. Mark or know the location of your electrical panel, since we’ll need to plan the power run for automation. If you have a homeowners association, check their design guidelines and bring any relevant documents to the consultation. We handle the technical specifications; you just need to know what you want the gate to do and who you want to let through.
Schedule Your Gate Installation Service in Johns Creek Today
Call (678) 394-1765 to schedule your free measure and written estimate. A live person will answer, gather your site details, and book a time that works for your schedule. You’ll receive an itemized, fixed-price proposal under Haven Standard Clause 1, with no obligation to proceed. Every installation we complete in Johns Creek carries the 365-Day Done Right Promise and leaves behind a documented photo record of what we built and how we built it.
Written by Adrian Vance, Owner at Vance Gate Repair, serving Johns Creek since 2014.